How to Apply TWP 100

TWP Stain Wet on Wet Application

by TWP Help April 11, 2022

posted by TWP Help

TWP with Wet on Wet Application Tips

TWP Stains are to be applied “Wet on Wet” when the wood is absorbent enough to handle more than 1 coat of the stain. This is typically for wood and decking that is older than 12 months and has been exposed to the elements. Applying the TWP “wet on wet” is similar to applying 1.5 coats of stain. The second coat covers twice as much square footage as the first coat.

Applying TWP “wet on wet” is very easy and not complicated once you understand the simple steps.

1,280 comments

How to Apply TWP 100 Stain Series

by TWP Help January 20, 2022

posted by TWP Help

Tips on Applying TWP 100 Pro Series in 2022

TWP 100 Series Stain

TWP 100 Stain Series Wood and Deck Protectant has a coverage rate of 150-300 sq. ft. per gallon, per coat. Best to measure the wood’s square footage to determine how many gallons you’ll need for your project. On wood decks, be sure to include all the railings and steps.

Before applying TWP 100 Series Deck Stain be sure the wood surface has been cleaned properly using a wood cleaner. Use a broom or leaf blower to remove any debris that may have fallen onto the wood since cleaning it.

618 comments

Applying TWP Wood Stain with a Sprayer?

by TWP Help January 20, 2022

posted by TWP Help

Update on Spraying TWP Wood Stains

TWP Stain Sprayer Application

Are you looking for a quicker, easier way to stain your exterior wood TWP Wood and Deck Stain? A low-pressure pump sprayer, HVLP Sprayer, or an Airless Sprayer can be a good choice but you will need to be careful with overspray and an even application.

Using these tips below will help to ensure your TWP Stain is applied evenly, with a faster application time, using a pump sprayer

See our official article and tips on this link: Applying TWP Wood Stain with a Sprayer

4 comments

The TWP Guide to Staining a Deck

by TWP Help January 20, 2022

posted by TWP Help

How To TWP Guide to Staining a Deck in 2022

Prolonging the life of a deck is not difficult if you know enough about deck care and regular maintenance. Every year or two most decks need to be cleaned and recoated with deck stain. This will not only enhance the natural beauty of the wood but will create a barrier of protection from Mother Nature. Once a deck has been prepped (See article: The TWP Guide to Prepping a Deck) it is then ready for a coat of TWP stain. This guide will help you along in getting a professional like finish.

TWP Stain Application Tools

88 comments

Rain Before and After TWP Stain Application

by TWP Help January 20, 2022

posted by TWP Help

Tips on Rain when applying the TWP Wood Stains 2022

When taking on a deck staining project there are a few important factors to consider. One of which is the weather. Rain is probably the biggest factor when staining a deck with TWP or any stain for that matter. Ideally, you will want to check the weather several days in advance before starting your project. Be sure there is no rain forecasted for the next several days. Prior to applying TWP Stain, you will want to wash the wood using a quality wood cleaner followed by a wood brightener product. This will clean the surface of the wood and prepare it for the new stain.

35 comments

Dry and Curing Time of TWP Wood Deck Stains

by TWP Help January 20, 2022

posted by TWP Help

Dry and Curing for TWP Stains. How long does it take?

It is good to know the dry and curing time of TWP (Total Wood Preservative) Stain prior to applying. Some people get in too big of a rush and want to start putting furniture, plants, grills, etc. back onto a wood surface too soon after staining. It is best to allow TWP to fully dry and cure before allowing foot traffic and items to be placed on the surface.

Drying and curing time for TWP may vary depending on climate and weather conditions. Over application can also affect dry and curing times. TWP should dry evenly flat with no glossy areas. Glossy areas indicate over-application of the product and will extend the dry and curing time of TWP. To avoid over applying TWP, allow the stain to soak into the bare wood for 30 minutes then wipe away or back brush any excess stain that has not penetrated the surface. Do not apply TWP if rain is expected within 48 hours. TWP can withstand light rain within an hour or so of being applied but it is best to wait for dry conditions prior to staining.

69 comments

TWP Stain is Spotty or Shiny

by TWP Help January 20, 2022

posted by TWP Help

TWPStainHelp.com Tips: TWP Stain Application is Spotty/Shiny and How to Fix

Staining a deck can be a challenge. There are some common mistakes that can occur that may greatly affect the final results. One such common mistake is over applying the stain.

With TWP Stain it is recommended to apply the stain using a brush, roller, or some type of sprayer. If the wood seems very thirsty, you can apply two “wet on wet” coats. TWP is a penetrating stain so you should never apply more stain than the wood can absorb. Once the stain as had 20-40 minutes or so to penetrate into the wood, you should go back and wipe away or back brush any puddles, drips, or runs.

307 comments

Best Results with TWP Stains

by TWP Help January 20, 2022

posted by TWP Help

How to Achieve Great Results with TWP Stains – TWPStainHelp.com Tips

When completing any exterior staining project you can achieve the best results by using a quality product and having the right knowledge. TWP wood stain will give you the best results possible but there are some general tips that can make the final results that much better.

One vital step that a lot of homeowners skip over is wood prep. Preparing the wood for the new stain is extremely important. Skipping this step will not allow the TWP wood stain to perform as it should thus shortening its performance and longevity.

42 comments

Stain All Sides with TWP?

by TWP Help January 20, 2022

posted by TWP Help

Stain All Sides of the deck board with TWP?

When staining a deck using TWP, is it necessary to stain all sides of each board? Consider the reason for staining wood – to shield it from weather damage, which causes rot and decay. This can lead to an unsightly appearance and structural failure.

Wood that is exposed to the elements will experience constant changes. Wood swells as it absorbs water and moisture, then shrinks when it dries out. These constant changes begin to break down the cellular structure of the wood causing it to crack, split, and warp. Ultraviolet rays fade and discolor the wood leading to a neglected appearance.

186 comments

How to Cleanup TWP Stain and Brushes

by TWP Help January 20, 2022

posted by TWP Help

TWP Stain Cleanup for Applicator Tools – TWPStainHelp.com

Once you have completed an exterior wood staining project using any of the TWP Series Wood Stains, you should clean up using mineral spirits. Although TWP is the only EPA registered wood preservative and has a very low VOC it is oil-based and requires mineral spirits for cleanup. But with some cleanup knowledge and tips, it can be a breeze.

43 comments