Tag:

How to Apply TWP 100

Prepping New Wood For TWP Stains

by TWP Help January 10, 2025

posted by TWP Help

TWP Stain Tips for New Wood Decks in 2025

Preparing New Wood for TWP Stains

When applying TWP Wood Stains to new wood for the first time, following the correct preparation steps is crucial. New smooth wood or decking is not ready for staining before installation or immediately after. Always adhere to the TWP Wood Stain guidelines rather than relying on advice from a lumber yard or paint store, as they may not fully understand the prep requirements for optimal results.

TWP and New Smooth Decking or Exterior Wood

New smooth wood is not sufficiently absorbent for TWP Stains due to higher moisture content and the presence of “mill glaze.” Mill glaze is a waxy film that forms during the milling process when high-speed blades heat the wood, drawing out sap and moisture. As this cools and dries, it creates a coating that prevents TWP Stain from properly penetrating the wood grain.

Important Note:

New Rough Sawn Wood/Fencing: Unlike smooth wood, new rough sawn vertical wood or fencing can be stained immediately after installation without waiting or extensive preparation, as it lacks mill glaze and is highly absorbent.
Ensure the rough sawn wood is fully dry before staining. If it has aged or oxidized (turned gray), prep it using the Gemini Restore Kit before application. For newly installed rough sawn wood, one coat of stain is usually sufficient.

Proper preparation ensures your TWP stain delivers its intended durability and beauty, whether you’re working with smooth or rough sawn wood.

2,352 comments

TWP Stain Wet on Wet Application

by TWP Help April 11, 2022

posted by TWP Help

TWP with Wet on Wet Application Tips

TWP Stains are to be applied “Wet on Wet” when the wood is absorbent enough to handle more than 1 coat of the stain. This is typically for wood and decking that is older than 12 months and has been exposed to the elements. Applying the TWP “wet on wet” is similar to applying 1.5 coats of stain. The second coat covers twice as much square footage as the first coat.

Applying TWP “wet on wet” is very easy and not complicated once you understand the simple steps.

1,496 comments

Applying TWP Wood Stain with a Sprayer?

by TWP Help January 30, 2023

posted by TWP Help

Update on Spraying TWP Wood Stains

TWP Stain Sprayer Application

Are you looking for a quicker, easier way to stain your exterior wood TWP Wood and Deck Stain? A low-pressure pump sprayer, HVLP Sprayer, or an Airless Sprayer can be a good choice but you will need to be careful with overspray and an even application.

Using these tips below will help to ensure your TWP Stain is applied evenly, with a faster application time, using a pump sprayer

See our official article and tips on this link: Applying TWP Wood Stain with a Sprayer

4 comments

The TWP Guide to Staining a Deck

by TWP Help January 10, 2025

posted by TWP Help

How To TWP Guide to Staining a Deck in 2025

Prolonging the life of a deck is not difficult if you know enough about deck care and regular maintenance. Every year or two most decks need to be cleaned and recoated with deck stain. This will not only enhance the natural beauty of the wood but will create a barrier of protection from Mother Nature. Once a deck has been prepped (See article: The TWP Guide to Prepping a Deck) it is then ready for a coat of TWP stain. This guide will help you along in getting a professional like finish.

TWP Stain Application Tools

98 comments

Dry and Curing Time of TWP Wood Deck Stains

by TWP Help January 30, 2023

posted by TWP Help

Dry and Curing for TWP Stains. How long does it take?

It is good to know the dry and curing time of TWP (Total Wood Preservative) Stain prior to applying. Some people get in too big of a rush and want to start putting furniture, plants, grills, etc. back onto a wood surface too soon after staining. It is best to allow TWP to fully dry and cure before allowing foot traffic and items to be placed on the surface.

Drying and curing time for TWP may vary depending on climate and weather conditions. Over application can also affect dry and curing times. TWP should dry evenly flat with no glossy areas. Glossy areas indicate over-application of the product and will extend the dry and curing time of TWP. To avoid over applying TWP, allow the stain to soak into the bare wood for 30 minutes then wipe away or back brush any excess stain that has not penetrated the surface. Do not apply TWP if rain is expected within 48 hours. TWP can withstand light rain within an hour or so of being applied but it is best to wait for dry conditions prior to staining.

81 comments

Properly Applying TWP Stain So It Does Not Dry Shiny

by TWP Help January 30, 2023

posted by TWP Help

TWPStainHelp.com Tips on Properly Applying TWP Deck Stains So It Does Not Dry Shiny

When applying TWP you should follow a few simple tips to get proper coverage and the look you want. TWP is not meant to give a “shiny” appearance. It is a deep penetrating wood preservative that soaks into the wood pores for optimal protection. TWP is a semi-transparent stain that adds color while allowing the wood grain to show through enhancing its beauty.

If TWP dries shiny then that suggests it was over-applied. In the case of applying deck stain, more is not always better. You only want to apply as much stain as the wood will soak up. Any extra puddles of stain that do not soak in will dry on top and give you an inconsistent shiny appearance. Not only does this look unappealing, but it also will not perform as expected.

26 comments

How to Apply TWP to a Fence

by TWP Help January 30, 2023

posted by TWP Help

TWPStainHelp.com Tips: How to Apply TWP Wood Stains to a Fence

Wood fences have been around for many years and can provide beauty, protection, and privacy to any home. Like other wood structures, wood fences need to be treated to keep them from becoming weather damaged. The key is to block out harmful UV rays and moisture. Using an easy to apply TWP formula wood stain can help preserve your fence for many years.

118 comments

TWP Stain is Spotty or Shiny

by TWP Help January 30, 2023

posted by TWP Help

TWPStainHelp.com Tips: TWP Stain Application is Spotty/Shiny and How to Fix

Staining a deck can be a challenge. There are some common mistakes that can occur that may greatly affect the final results. One such common mistake is over applying the stain.

With TWP Stain it is recommended to apply the stain using a brush, roller, or some type of sprayer. If the wood seems very thirsty, you can apply two “wet on wet” coats. TWP is a penetrating stain so you should never apply more stain than the wood can absorb. Once the stain as had 20-40 minutes or so to penetrate into the wood, you should go back and wipe away or back brush any puddles, drips, or runs.

340 comments

Best Results with TWP Stains

by TWP Help January 30, 2023

posted by TWP Help

How to Achieve Great Results with TWP Stains – TWPStainHelp.com Tips

When completing any exterior staining project you can achieve the best results by using a quality product and having the right knowledge. TWP wood stain will give you the best results possible but there are some general tips that can make the final results that much better.

One vital step that a lot of homeowners skip over is wood prep. Preparing the wood for the new stain is extremely important. Skipping this step will not allow the TWP wood stain to perform as it should thus shortening its performance and longevity.

48 comments

Application Instructions for TWP Stains

by TWP Help January 30, 2023

posted by TWP Help

The Application Instructions – TWPStainHelp.com

You have made the decision to use TWP wood preservatives to ensure the lasting beauty of your exterior wood surfaces. By using TWP deck stain and following some helpful guidelines you can get professional-like results.

Before applying TWP wood stain it is important that the wood is cleaned and prepped correctly so the stain will perform as expected. Clean the wood using a wood cleaner and a stiff brush or pressure washer to agitate the wood and remove any unwanted contaminants. We recommend using a product like the Gemini Restore-A-Deck Kit. This is a two-part deck restoration system containing a deck cleaner and brightener that is extremely effective and eco-friendly.

143 comments