Last Updated on April 16, 2024 by TWP Help
The Official TWPStainHelp.com Guide to Prepping a Wood Deck
With wood decks maintenance is vital to the structural integrity of the wood. Cleaning, prepping, and staining a deck are the 3 main keys to deck care. With any deck stain, including TWP the prep work is crucial. No matter how superior the deck stain is it will not perform properly or give you the results you expect if the wood is not prepped correctly. The following is a TWP guide to prepping a deck that has never been stained or currently has TWP stain already on the wood. If you have a stain of a different brand, you will need to remove it with a stain stripper. See this for more info Switching to TWP Stains.
Cleaning the Deck for TWP Stains
Prior to staining with, TWP the deck needs to be cleaned thoroughly to allow for proper stain penetration. Use a quality wood cleaner like the oxygenated cleaner Gemini Restore-A-Deck. These types of cleaners are safer on the wood than bleach-based cleaners and will effectively remove dirt, mold, mildew, and grayed wood fibers. It is important to get back down to clean bare wood. Apply the wood cleaner as suggested by the label instructions. Let the cleaner dwell and soften up the pollutants before using a scrub brush or performing a light pressure washing.
If an old failing stain is present it must be removed. A wore down semi-transparent stain may clean off with an oxygenated cleaner. If the old stain is stubborn then you might have to use a wood deck stain stripper instead of a cleaner. Once the pollutants and any remnants of old stain are gone the deck should look new again.
Using a Deck Brightener with TWP
A deck brightener also called a neutralizer is the next step after cleaning. Because the cleaners and/or strippers are caustic in nature they need to be neutralized. Apply the deck brightener immediately after cleaning and according to the directions. Then allow it to dwell for several minutes before rinsing off with water. This will lower the pH level of the wood and make the wood grain “pop”. This acidic nature of the wood surface will allow TWP stain to dive deep into the wood and result in a more professional like finish.
Dry Time for TWP Stains
After cleaning and brightening the deck it needs to dry prior to staining. With a moisture meter, you want 15% or less moisture content before applying the stain. If you do not have a meter, typically 1-2 days of dry weather is adequate time for the wood to dry completely. Now the deck is ready for TWP stain. Following this TWP guide to prepping a deck will ensure the stain lasts longer, enhances the appearance, and performs as expected.
Hi, my deck hadn’t been sanded in 10 years so sanded with 60-80 grit. Can I just do wood brightener step, let dry, then stain? Or do I have to use the cleaner step then brightener? If it’s raining today, Sunday, is drying all day Monday and Tuesday safe to start staining Tuesday afternoon or should I wait until Wednesday? Also, how long does freshly stained deck have to be dry before it’s safe for rain? 12 hours? 24 hours? Last, if I mix the 100 series Pecan and clear to lighten it some, it should still have enough pigment to protect from graying right? I’m thinking 50/50 mix. My deck is full sun.
Thanks
The cleaner and brightener is best. 48 hours at minimum after rain or prep. If you mix 50/50 you will reduce the UV protection by 50%.
Thank you! What is dry time after stain application before it’s safe to get rained on?
Hello. I have a question regarding when to reapply 1500 series stain. I initially applied 1500 series to my deck after completely sanding off previous products in the spring of 2019.. I was very happy with the results and with the product’s performance during the “deck” season of 2019 here in CT. The deck seems to have developed some mild staining (mildew?) on some of the planks in the meantime. The planks still seem to “bead” water when it rains even though the color may have faded a bit since last year. My question is when might it be best to apply a “refresher” coat of your product to spruce things up a bit and provide added protection. I am concerned that trying to apply such a coat now will not penetrate (as the water is beading after all) and dry on the plank surface…which I understand to be a real problem. I have included photos of the application to my decking, the first photo from 2019 (without the stone shows the initial application. The seconf photo (with the stone) shows the current 2020 condition of the stain with some of the typical mild black staining that can be found elsewhere on the deck in some places (maybe where water “stands” after the rain?). What is your folks’ advice for the re=application of your product in these circumstances? Very happy with your product and the results and I DON’T want to mess it up by reapplying inappropriately. THANKS!!! Michael from CT 🙂
If you prep with the Gemini Kit then the new coat of TWP will take: https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit
Hello! What’s the difference between the Safe Strip stripper (1 step; no brightening step needed) and the Restore-A-Deck Stripper & Brightener? We would be stripping one light coat of TWP 100 Series stain that was applied improperly. Can we get by with the Safe Strip product to prep for the re-stain, and avoid the 2nd brightener step? The TWP stain coat was misapplied about 6 months ago and the wood is now just over a year old. It’s not in terrible condition; the stain just wasn’t completely brushed in like it should’ve been. Would either stripping product/process work, or is there a compelling reason to do the more onerous (i.e., more time-consuming & expensive) 2-step stripping/brightening process? Thank you for your helpful & generous advice!
The RAD Stripper works better for removing this.
I power washed half of my deck to see if it would be sufficient or not. Do I need to remove every bit of old TWP if I am reapplying the exact same one?
No. It looks good to stain.
So I don’t need to do anything else beforehand?
No.
Hi, curious if there’s any change when applying the cleaner and brightener to vertical surfaces? I cleaned/brightened/stained my cedar deck last fall, though I was not able to get to it all. I have the stairs left to do as well as the band boards that wrap around the entire deck, these band boards are the “vertical” surfaces I am referring to. Just curious if there’s any other guidance with these vertical boards since the cleaner/brightener won’t sit on top and work like they do with the horizontal boards.
Another topic, do I need to protect the previously stained wood from the cleaner/brightener? Cover with plastic before doing the surfaces that I was not able to get to last fall?
Just apply the cleaner and pressure wash off after 10 minutes. Same with the Brightener but just rinse the brightener.
It should not harm the stained wood if splashed on, just rinse within a few minutes.
Thanks – can I apply the cleaner to wet wood? As in it rained and the wood is still wet, but I’d still like to start the job.
Yes.
I just received your stripper, brightner and 1500 stain. I’m replacing the deck boards this weekend with red cedar. I’m leaving the rest of the deck in place, but will need to strip it. Should i do it all at once after i install the new cedar? Will the stripper hurt it? Or should i strip it now and then brighten and stain everything later?
You cannot stain new wood right away: https://twpstainhelp.com/prepping-new-wood-for-twp-stains/
Strip it now. Install the new wood, let that weather for 4+ months, then clean and brighten all for final prep.
In the summer of 2019, I properly prepped and applied one coat of TWP stain on my pine deck, installed in October 2018. It is now time to apply the second coat of TWP. The deck wood looks in great shape. What do I need to do before applying the second coat of TWP stain? Do I have to use a cleaner since the previous stain was applied only a year ago? If so, what do I need to use to prepare for the second stain application?
Use this kit for the prep: https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit
Hi,
TWP1500 has been purchased. I’ve read a lot but still unsure.
Please advise stain process for the flw:
A) Phoenix, Az — temperature range 30-120 degrees
B) 150 sq ft deck + 2 steps in full sun
C) guessing pine with no mold or mildew.
D) original stain: existing stain is approx 4 years old. brand unknown. guessing semi transparent applied to new wood. see photo #1 for our starting point.
E) We inherited the deck so some answers are unknown.
1) Deck sanded 6 weeks ago – photos 2 and 3. Did we sand enough? See photos attached. Should we keep sanding until all previous product is gone? Read that too much sanding will undermine stain penetration.
2) Then power wash?
3) How many coats of stain?
4) Is it ok to use exterior wood filler product prior to stain application?
5) And then should we repeat same process every 2-3 years or just add a coat of stain?
We appreciate your generosity…thank you in advance. With your guidance I believe we can do it right the first time!
1. Do not sand anymore. Finish the removal with RAD Stripper Kit: https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail
2. Yes, while using the Stripper Kit.
3. Never use wood filler on decks, it does not blend or work.
4. Clean and recoat every 2-3 years as needed.
Thanks
As we were applying brightener, it started raining. The exposed areas of our deck didn’t really change colors like the covered portion, so we assumed the rain was diluting the brightener. This led us to increase the brightener concentration a bit in those areas. Now it looks much more consistent, but the wood has fuzzing. We used a deck sander and *lightly* sanded those areas to remove the fuzz. Should we use brightener again?
Yes, brighten all again.
We used a stripper, scrubbed and power washed our deck, then called it a day. We did not apply brightener as it rained the next day. It has been a week, and the wood is nice and dry. Do we 100% need to apply brightener still?
Yes.
I am creating a deck table with a live tree stump that intentionally comes up through our deck, but accidentally applied TWP protectant without bleaching the surface. The plan is to add an outdoor varnish when completed with TWP. Have I botched the job by not bleaching first?
You cannot topcoat TWP with a varnish and using varnish on outside wood is a bad idea. It will peel and blister. Not brightening the wood is not going to cause any issues.
Cleaned and brightened with pressure washer, but still had some solid stain so we went ahead and completely sanded everything. Question – do we need to re-brighten/clean or can we just use pressure washer, wait 48 hrs then stain?
Clean and brighten after the sanding to open the wood grain better for the stain.
We are getting ready to stain our deck. we constructed it summer of 2018. Planning to prep deck for staining with Gemibi restore a deck cleaner and brighter. Our deck rails have aluminum spindles with a black powder coat smooth finish on them. Will we need to protect them from the cleaner and brightner. Secondly will we need to protect them form the Cedar Tone 101 stain or can they be wiped off afterwards.
Best to test first with the cleaner and brightener to see if any reaction with the spindles, typically there is not. If smooth-coated spindles the stain will wipe off. If more if a rough texture, it will not.
I mixed 3 gallons of Restore-a-deck cleaner and haven’t been able to use it for several days. I put it in a sprayer with the top closed but unpressurized. After about 5 hours enough pressure built up in the sprayer to almost split it. Two questions: Will the mixed cleaner normally build up pressure in a closed container if not used immediately, and how long will mixed cleaner remain effective?
The cleaner is oxygenated and has to be used within 6 hours of mixing.
I’ve built a kitchen cypress table that will never be outdoors. I would like to keep it a little rustic so I am thinking about using Dark Oak 103. It is not necessarily new cypress but is not sinker cypress either. I have sanded with 180 grit, do I use Gemini Restorer before applying Dark Oak Stain?
You sanded too fine. Let weather for a couple of months and then clean and brighten for prep with the Gemini Kit.
I am refinishing with 1500 Cedartone after two years. I have to replace one board because of splitting and I need to flip another board over because of cupping. Those boards are marked with an “X” in the first photo. Since I will now have a mix of old, new, and unstained wood, what steps do I need to take before applying the stain? The pics below are of my deck after having been power-washed. You can also see some areas which are darker, where my patio furniture sits and, I assume, offer more protection from the weather. Thank you in advance for your instruction!
Prep all with this: https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit
The two boards will need a light recoat next year.
My pressure treated pine deck has not been sealed or stained. It is 4 years old. I am cleaning it with restore a deck in about an hour.
– Do I wet the deck first before applying the cleaner?
– The deck has green algae on it. Should I apply bleach and water after brightening? or before brightening or not at all.
Thanks,
Diane
-Yes on wetting first.
-The cleaner should remove the algae.
I have a redwood deck. 5 years ago I used Gemini stripper and Brightener and TWP stain.
I have attached photos. As you can tell, portions are exposed to more sun than others. Should I use the Gemini cleaner and Brightener or Gemini stripper and Brightener before additional stain?
Use this: https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail
We stained our deck with your 1500 2 years ago and now trying to restain, weather permitting. We power washed with your cleaner and then applied brightener, 2 weeks ago and now wanting to apply the stain, but rain in forecast 24 hrs. after application. My understanding is we should hold off? If we hold off can we just use garden hose sprayer to clean deck and then 48 hrs. later apply stain?
24 hours after the application is fine.
I’ve stripped and brightened my 20 year old pine log outdoor furniture. Which TWP product should I use? Do 2 wet on wet coats? Can I order color samples to try on the furniture!
Use the TWP 1500 Series. Samples are here: https://www.twpstain.com/stain-samples
I used Oxiclean to clean my furniture after stripping. Is that considered a brightener or do I need to use an actual brightener after palm sanding?
No, that is not a brightener. You should use a brightener.
Is there a performance difference between 100 and 1500 for log furniture? I’ve stripped and brightened the furniture, then palm sanded with 60 grit. I’ll blow the dust off with a leaf blower. Am I ready to apply the stain? 2 coats?
No, they will last about the same. You should be good to stain now as long as previous coatings have been removed.
So I had my outdoor covered porch redone using your product. The contractor DID not follow the instructions on the can. He applied the stain….came back the next day …said it was “wet” and then reapplied the following day. I got a hold of what he was using and read the application instructions. Never waited & wiped up….now it’s has that streaked “wet” look. My biggest concern will it still be an effective barrier for the floor from the elements? Thanks for any guidance you can provide.
It will be fine, just may take longer to cure and dry.
I replaced my pressure treated decking last year so all of the wood is properly acclimated and weathered. I’d like to stain now, however, I want to level out bows and cups in the boards with a deck sander first. Do I need to wait again after sanding before applying TWP 100, also is there a certain level of sanding grit I should use so I don’t negatively impact absorption?
No finer tan 80 grit. After the sanding, you should wait about a month and then prep with the Gemini Restore Kit. Just one coat of stain for this newer deck.
We stripped the deck and have some guys who are going to lightly sand and stain. Can I use the brightener beforethey sand or must iuit be done afterwards ?
After.
If I have your stain on my deck now. Does it have to be completely removed before I can put more stain on? Restraining would be after using the restore a deck. From reading it sounds like that would be the first step, correct?thanks
No need to strip. Use the Gemini Restore Kit for prep.
We used TWP Series 100 4 years ago and absolutely LOVE it. It needs to be redone as I have some areas of wear and mold/mildew. I think I should use the Gemini cleaner to prep–correct? I would like to use the same color again. Unfortunately, I don’t remember what color it was. Can the order desk look up that info for me?
Thanks so much!!
Yes, use the Gemini Restore Kit for prep. We sent an email with a copy of your last order to you.
What is the difference between the RAD Stripper and Brightener Kit and the Gemini Restore a Deck Kit? Is there a reason you would use one over another?
Thanks,
Gemini kit contains a cleaner, not a stripper.
Here are the pictures of my fence. Cedar. About 11 months after installation.
What do you recommend. And again: thanks!
Use the Gemini Kit for the prep: https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit
I believe I followed all directions with the Gemini product…why might I have these discolored areas close to the knots in my cedar? What did I do wrong?
Thanks again!
That is normal and is part of your wood grain.
Staining deck and fence once we get enough dry days!
Posting deck pictures here, will post fence in another thread.
Deck is pressure treated pine, installed about 11 months ago. What do you recommend? Pre treat or just stain? Appreciate any advice!
Matt
Use the Gemini Kit for the prep: https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit
Apply the cleaner and then pressure wash off. Apply brightener after the cleaning is done and then rinse.
Hi, I applied TWP 100 to new deck approx 1 year ago and it developed these black streaks. I just cleaned and brightened w Gemini kit but it still has some old TWP showing in some areas. Can I recoat over this or does 100% of old TWP need to come off.
I can take a pic of cleaned deck tonight.
Post a picture after the prep. TWP does not turn black so it must have been something else that caused the streaks.
Exactly one year ago, we applied TWP stain 100 on our new deck which had cure for year. We did all the appropriate prep work and are now ready (1 year later)to put a second coat of TWP 100 stain on our deck. We pressure washed the deck with water only. Is it necessary to use Gemini restore a deck and then the deck brightener again before applying the second coat?
Post a picture, please.
I have attempted to attach for photos. Please let me know if they do not appear on your end, thanks
You should be okay to stain.
Hey there, I have an old and unloved mahogany deck which has been exposed to Massachusetts winters and summers.
It had a patchy solid stain coat on it but about a quarter of that stain had worn off and the deck was exposed to the elements. I sanded, cleaned and brightened the deck but in the most shaded area of the deck the color is not uniform, I presume that this is water damage which is irreparable right? My main question is would the TWP semi-transparent stain work on my deck and make the overall color uniform? We are looking at going for the Rustic color.
The TWP would not make this perfectly even. The internal discoloration that you have would still show as darker in spots when stained with a semi-transparent stain like TWP.
Hello, I used TWP 100 Pecan on my aged new wood porch in Fall 2017. Applied a deck cleaner and was going to apply a second coat this Spring 2018 but wasn’t able to apply second coat. Should use the Gemini Kit before a second coat this Fall 2018?
Yes, that would be the best way to prep.
Hi, I stained my deck last year with TWP 1500. I had to use the stripper and brightener because it had other stain on it. I only did one coat. Should I do a second coat this year or is next year ok?
Once I am going to do it, do I use the regular cleaner only or the cleaner and the brightener? Can I do all the cleaning with just a garden hose or I have to use a power washer again? I don’t want to strip it down again with a power washer I just want to light clean it so I can do a second coat.
Thanks for any help.
Do it next year. Just lightly wash with soapy water (dish soap) and rinsed with water for the prep if doing a maintenance coat within 12 months. If over 12 months use the Gemini Cleaner for prep.
Next year will be 2 years,more than 12 months, so use the Gemini cleaner and brightener or just cleaner or just soapy water?
Thanks
Gemini Restore Kit.
OK thanks. When using the Gemini kit (not the stripper) do you always have to use the cleaner and the brightener even though it already has stain on it?
Yes.
I recently purchased a home with an 8 year old wooden deck (I’m not really sure of the wood type). In those 8 years, I know that it was only stained once using a transparent stain. Needless to say, it needs some care. So I’ve purchased the Restore-a-deck cleaner, Restore-a-deck brightener and 5 gallons of TWP 1500. My issue is that I somewhat foolishly aggressively power-washed about 1/3 of the deck before reading that this could cause ridges (which it did) that could eventually lead to splintering. So what is my best way forward? I can sand the part that I already power-washed. Will that even help prevent the future splinters In that case should I sand the rest of the deck too? Should I just power-wash the rest of it too for the sake of consistency (I’m guessing not).
In short, what’s the best way forward for stain prep on a deck that has been partially (aggressively) power-washed?
Thanks!
Used the Gemini deck restore this weekend to prep for restaining with 1500. Deck has a 2 year old coat of 1500 that was failing a little in high traffic areas. The 1st step of the Gemini kit removed a lot of the original coating which surprised me. Just used a pump sprayer and scrub brush. Should I repeat the process to remove all of the old coating? I’ll be using the same color of 1500 for application.
Yes, that would be best. You will have a more even appearance this way.
Can I apply the Gemini RAD with a pressure washer? Can I mix it more concentrated so the washer doesnt dilute the solution?
No. It is not possible to inject the products through a pressue washer. It will not be effective.
What needs to be done to prep an old, mostly sound deck that was painted with what appears to be water based deck paint, top and bottom surfaces…several storeys tall.
The paint is mostly there except for the surfaces that are walked on and exposed to the elements.
What would work best in this case? Should I simply match the color and keep adding paint?!
Thanks
TWP is not a paint but a semi-transparent stain. To be able to use the TWP on your deck that is already painted, you must 100% sand off the paint first.
We stained our porch with TWP 1500 series 2 years ago. It held up great but is now ready for a maintenance coat of the same color. My husband used the Gemini Clean and Brighten kit 2 nights ago. It left some of the wood looking very splotchy with patches of stain remaining. Will it be okay to just stain as per directions? Or do we need to clean it again? Picture is attached.
It would be best to clean again so it has a more unifrom appearnce when stained.
This is more than a question. You must be very careful using the stripper restore part of the process. I had everything all set and ready to go and I used a very thick glass container to mix the first part of my solution. It exploded. Luckily there was no damage to me, but it could’ve been very serious. I understand after discussion with your customer service that you Will send me some more stripper powder but I highly suggest you put a warning out to everybody about this I do not see any mention about not using glass containers in any of your information online.
Will try again next week when the replacement stripper comes in !
What is the difference between the two stripping products you sell? I think one is Safe Strip and the other Strip A Deck.I’m trying to remove a 7 year old semi transparent TWP stain.
Hello, the Restore A Deck Stripper is a stronger product for removing old coatings. We suggest using this.
resoning
Stripped and brightened our deck and now there are wood fuzzies all over. Do we have to sand these?
You do not have to as they tend to not show when the TWP stained is applied. If you want lightly sand, use 80 grit paper.
Back in June of this year, I prepped and stained our two year old, never been stained deck (cedar supports & trim and pressure treated decking) according to instructions given on the website. It was in the mid-90s when I stained it, and I don’t think I did the wet-on-wet application properly, as it is already showing “dry” or very light looking spots. So I’d like to re-stain to protect it over the coming winter. There is minimal mold/mildew, mostly dirt and dust. What type of prep should I do? Do I need to start from scratch with the cleaner/brightener?
Yes redo with the Gemini Restore Kit as the prep.
Looks like it was too hot and flash dried on you.
I have a pine deck that I have your 1500 cedar tone stain on and want to go back to a clear or natural look. I have pressure washed it and removed a lot of the stain. what do I need to do to prep the wood before going to a clear or natural stain? Part of the deck is covered and part of it is exposed.
Use the Restore A Deck Stripper Kit:
https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail
Powerwashed the deck ( about 8×30) last year, made of yellow pine pressure treated lumber about 7 years old now. But the guy who did it used some chlorine bleach in the mix with the power washer. He then stained it with 5 Gal of TWP 1500 cedartone which I purchased from you. All the vertical surface still have their color and look great, but all horizontal surfaces outside the soffets over the deck, and top rails have lost their color tone and look a dull dark brown to grey. Deck gets about 3 hrs sun per day. The areas under the 3 ft soffets which are 12 ft above the deck, did not turn this dull color. Any ideas?
Lightly clean and prep with the Gemini Kit all the horizontals and stain again with the same color..
Hello, I started the proccess of staining my cedar deck today by using the restore a deck cleaner. I used it all and with using a powerfull tip on the hose it got alot of the dirt, mildew, and grey up but I noticed when I used a scrub brush more was coming up. It got too late and I wanted to redo the cleaning so I didnt use the brightener. Also, there is a white haze in spots. I rinsed well but I read elsewhere that this haze is like a fuzz of old wood fibers. They recommend renting a buffer and use a 60 grit pad to gently remove the fuzz. Should I do this and then do the brightner? What about all the dirt and grime? Should I also redo a cleaner and scrub well before doing the other 2 things? Im a rookie and I want my deck to turn out nice. Help!
Did you use a pressure washer? That would have helped to remove the oxidation (white fuzz). Please send a picture.
I used a gutter cleaning spray tool which seems to be pretty powerful. Im finishing the ipper part using oxiclean and laundry detergent. Its working but Im having to scrub the dirt off. Will brightner help or will I need to sand?
You are not using enough “pressure” to remove all of the gray oxidation. Best to reclean and use a pressure washer. Another option is to sand or buff off. Brighten after. One other tip, most of this will not show when stained as the wood does darken.
I re-cleaned it but I dont have a power washer. I used alot of elbow grease with a brush.
Does this sound right?
1. Let dry completely
2. Sand or buff
3. Wash off and get completely wet.
4. Spray with brightner.
5. Wash off completely.
6. Wait 48 hrs and then add stain.
If I do stain without sanding, can I remove the fibers after staining if they show up? Thanks again for the help.
Steps sound correct. You cannot remove the wood fibers once stained.
Hello, My question is in regards to colour. Living in Toronto Canada I want to try the TWP 200 stain. I want a natural cedar colour and looking at your chart I am thinking of the Cedar Gold. The Cedartone seems to be more on the brown side. The stain I am replacing is the Flood UV5 Cedar. Any recommendations?
There Cedar Gold is a very popular color and a lighter tint than the Cedartone.
I followed all the steps last year and the deck looks great. I just want to do a cleaning this spring. What products & techniques do I need?
Are you reapplying another coat?
No, I just want to clean it. I used 1515 honey tone.
Try warm water with some dish soap and a soft car wash brush.
I stained my deck 2 years ago using TWP 105 Cape Cod grey.
I want to re-apply the same. What prep work do I need to do?
Prep with the Gemini Restore Kit.
Thanks. I just tried to order it and it appears it can’t be shipped to me anymore. It suggests using 1500 series but there is not a Cape Cod grey. What can I do?
I am sorry but there are not any gray colors in the 1500 Series and the 100 Series is restricted in certain stains. You could strip it down and go with a different color of the 1500. What state are you in?
I have a partially stained covered deck. Some areas, like the underside of the roof were never stained so it’s just dirty. I also replaced a number of boards last summer (from your postings, I decided to give the wood a full year to dry out).
Here’s my question – it appears to strip and restain the deck will be a 3 step process. Please tell me if I’m right:
1. Strip deck using Step 1
2. Neutralize stripped area using Step 2
3. Go over entire deck (including originally unstained areas) with “Restore-A-Deck” to clean.
No need to use the cleaner in the same areas you are stripping.
1. Strip what needs to be stripped.
2. Clean the dirty areas.
3. Brighten all when done.
Thanks. And I need to use “Gemini Restore-A-Deck” for #2 and “Restore-A-Deck Step 2” for number 3.
Yes.
A final question – I see a brightener that comes with the Restore a deck kit and a brightener that comes with the stripper package. Are these two brighteners the same?
Yes they are.
My deck was built four summers ago, stained the following summer then re-stained last summer. This summer I need to sand the deck. It has some slightly warped boards and several sections with large splinters of wood out. Do I need to clean the deck with the Gemini cleaner after sanding or just get the sawdust out? I’ll be filling in some of the cracks with filler. Does your stain cover the filler OK? Lastly can I use your stain on deck furniture? I have a chair made with eucalyptus wood that needs re-staining.
You should not use wood filler on exterior wood. It will not blend with the stain and will not properly work either. Yes, you should use the Gemini Kit after any sanding. The TWP should work on wood furniture as long as it prepped and applied correctly.